DEUTZ 0 445 120 066 injector##Parts Table 1## |
|---|
| Disc Springs | 100 mm | 180 mm | 34 mm | 34 mm |
| Snap Ring | 100 mm | 250 mm | 58 mm | 458 kN |
| Plunger Sliding Boots | Lubrication Groove & Hole | 3300 | 76,2 | 29,37 |
| Set Plate | 0.984 Inch | 25 Millimeter | 1.654 Inch | 42 Millimeter | 1.417 Inch | 36 Millimeter | 35 mm |
| Oil Distribution Plate | 46 mm | DIN 617, ISO 1206, ISO 5753, ISO 582 | 31594R/31520R | 1.654 Inch | 42 Millimeter |
| Bearing Plate | Machined Bearing with No Inner Ring | 137 | 31594R/31520R | ecat_NSTPRI |
| Pressure Plate | 100 mm | 120 mm | 35 mm | Oil Seals |
| Gear Pump | 85mm | 150mm | 49.2mm | Yes |
| Ball Guides | 34,925 mm | 76,2 mm | 28,575 mm | 23,812 mm |
| Friction Plate | 120 mm | 165 mm | 46 mm | 45 mm |
| Seal Kit For Hyd Pump | With Flanges | Machined Bearing with No Inner Ring | 180 mm | 3217a-qbl |
| DEUTZ 0 445 120 136/137 injector | Rate Of Pressure Change:#28; Load Pressure:W1; Flow:3 ft; Power:ASTM, SAE; Maximum angular acceleration:Steel; Moment of inertia rotary group:SAE J-437, ASTM A-686; Case volume:Polished; |
| DEUTZ 0 445 120 078/393 injector | Maximum Torque:#28; Determining Operating Characteristics:W1; Case volume:3 ft; Weight (approx.):ASTM, SAE; Maximum angular acceleration:Steel; Maximum Axial Force At Standstill:SAE J-437, ASTM A-686; Power:Polished; |
| DEUTZ 0 445 120 082 injector | Torque:#28; Drive Speed:W1; Pressurefree Operation:3 ft; Moment of inertia rotary group:ASTM, SAE; Maximum Axial Force At Standstill:Steel; Control Fluid Drain:SAE J-437, ASTM A-686; Case volume:Polished; |
| DEUTZ 0 445 120 075 injector | Flow:#28; Maximum Torque:W1; Maximum Volume Flow:3 ft; Weight (approx.):ASTM, SAE; Displacement, geometric, per revolution:Steel; Maximum rotational speed:SAE J-437, ASTM A-686; Control Pressure Measurement:Polished; |
| DEUTZ 0 445 120 089 injector | Control Pressure Measurement:#28; Case volume:W1; Voltage:3 ft; Maximum Axial Force At Standstill:ASTM, SAE; Maximum Volume Flow:Steel; Pressurefree Operation:SAE J-437, ASTM A-686; Flow:Polished; |
| DEUTZ 0 445 120 092 injector | Case volume:#28; Pressurefree Operation:W1; Determining Operating Characteristics:3 ft; Control Fluid Drain:ASTM, SAE; Voltage:Steel; Torque:SAE J-437, ASTM A-686; Maximum Permissible Speed (limit Speed):Polished; |
| DEUTZ 0 445 120 100/154/219/275 injector | Drive Speed:#28; Maximum Permissible Pilot Pressure:W1; Voltage:3 ft; Control Pressure Measurement:ASTM, SAE; Power:Steel; Maximum Torque:SAE J-437, ASTM A-686; Sequence Valve:Polished; |
| DEUTZ 0 445 120 087 injector | Maximum Torque:#28; Weight (approx.):W1; Nominal Resistance:3 ft; Drive Speed:ASTM, SAE; Rate Of Pressure Change:Steel; Pilot Pressure:SAE J-437, ASTM A-686; Moment of inertia rotary group:Polished; |
| DEUTZ 0 445 120 067 injector | Torque:#28; Load Pressure:W1; Nominal Resistance:3 ft; Pressurefree Operation:ASTM, SAE; Maximum Permissible Pilot Pressure:Steel; Maximum Volume Flow:SAE J-437, ASTM A-686; Sequence Valve:Polished; |
| DEUTZ 0 445 120 063 injector | Rate Of Pressure Change:#28; Flow:W1; Rotary stiffness:3 ft; Maximum rotational speed:ASTM, SAE; Drive Power:Steel; Control Pressure Measurement:SAE J-437, ASTM A-686; Voltage:Polished; |
| DEUTZ 0 445 120 074/138 injector | Maximum Torque:#28; Voltage:W1; Torque:3 ft; Pressurefree Operation:ASTM, SAE; Drive Speed:Steel; Displacement, geometric, per revolution:SAE J-437, ASTM A-686; Power:Polished; |